Product ID:MOLECULAR SIEVE TYPE 13X
MSDS Date:03/01/1995
FSC:6850
NIIN:01-112-6490
MSDS Number: BXQGH

UOP INC

25 E ALGONQUIN RD
DES PLAINES, IL 60017-5017
US

Emergency Phone: 708-391-2123/800-424-9300(CHEMTREC)

Info Phone: 708-391-2123/FAX 708-391-2953

Cage: 02QC3

UOP LLC

DES PLAINES, IL 60017-5017 US

Telephone: 847-391-2953

Cage: 02QC3

SILICA GEL (SILICON OXIDE)

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: <60%

OSHA PEL 6 MG/M3

ACGIH TLV: 10 MG/M3

ALPHA-ALUMINA (ALUMINUM OXIDE) (SARA 313)

CAS: 1344-28-1

RTECS: BD1200000

Fraction By Weight: <40%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9495

SODIUM OXIDE

CAS: 1313-59-3

Fraction By Weight: <20%

MAGNESIUM OXIDE

CAS: 1309-48-4

RTECS: OM3850000

Fraction By Weight: <5%

OSHA PEL 15 MG/M3 PARTICULATE

ACGIH TLV: 10 MG/M3; FUME; 9495

LD50 LC50 Mixture:SIMILAR COMPOSITION LD50 ORAL,RATE>5G/KG
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PROD INGEST UNLIKELY IF PROPER
SAF/HYGIENE PROCEDURES FOLLOWED.SKIN:IRRIT.MATL BECOMES HOT WHEN
1ST COMES INTO CONTACT W/MOISTURE.HOT MATL COULD CAUSE THERM
BURNS.EYE:DUST &/OR PROD DISCOMFORT &/OR IR RIT.INGEST/INHAL:PROD
GETS HOT IF ADSORBS WATER/PROD HEAT IF ABSORBS WATER.BURNS TO MOIST
BODY TISSUES IF CONTACT PROLON
Explanation of Carcinogenicity:PER MSDS:SILICON OXIDE NOT CLASS AS
HUMAN CARC (GRP 3):IARC. NTP/OSHA:PROD NOR COMPONENTS
CLASSIFIED/REG.
Effects of Overexposure:SKIN:IRRIT, THERMAL BURN. EYE:IRRIT, TEARING,
REDDENING. EYE:DISCOMFORT, IRRIT. INGEST/INHAL:BURNS TO MOIST BODY
TISSUES IF CONTACT PROLONGED.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
TARGET ORGANS:PROLONGED/REPEATED EXPOSURE MAY CAUSE LUNG INJURY.

First Aid:SKIN:WASH AREA W/SOAP/WATER. IRRIT DEVELOPS OBTAIN MED ATTN.
EYE:FLUSH W/WATER FOR @LEAST 15MINS. IRRIT OCCURS OBTAIN MED ATTN.
INGEST:DRINK 2 GLASSES OF WATER. NEVER GIVE ANYTHING BY MOUTH IF
LOSING CONSCI/IS UNCONSC/IS CONVULSING. OBTAINMED ATTN.
INHAL:REMOVE TO FRESH AIR. RESP PROBLEMS DEVELOP OBTAIN MED ATTN.
NOTE TO DR:PROD A DESICCANT, GENERATES HEAT AS ADSORBS WATER.USED
PROD CAN (SUPPLE)

Flash Point:WILL NOT BURN
Extinguishing Media:USE MEDIA APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:USED MATL MAY CONTAIN PRODUCTS OF HAZ NATURE.
USER OF PRODUCT MUST ID HAZARD OF RETAINED MATL & INFORM FIRE
FIGHTERS OF THESE HAZ.
Unusual Fire/Explosion Hazard:USED MATL MAY CONTAIN PRODUCTS OF HAZ
NATURE. USER OF PRODUCT MUST ID HAZARD OF RETAINED MATL & INFORM
FIRE FIGHTERS OF THESE HAZ.

Spill Release Procedures:LG:CONFINE ENTRY TO THOSE PROPERLY
PROTECTED.SEPC ATTN SHOULD BE GIVEN TO EYE/RESP PROT BECAUSE
RECOVERY OF DRY MATL EXPECTED TO GENERATE DUST.SWEEP/SHOVEL/VAC
INTO APPROPRIATE CNTNRS.SM:SWEEP/VAC INT O APPROPRIATE CNTNR.PROD
DISPOSED IAW ALL GOVT REG
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN TIGHTLY CLSD PROPERLY
LABELLED CNTNR.AVOID EYE CONTACT/INHAL/REPEAT-PROLONG SKIN CONTACT.
Other Precautions:FRESH UNUSED STATE PROD NOT FLAMM.EXPO TO WATER PROD
CAN GET HOT.1ST WETTED PROD CAN HEAT UP TO BOILING PT OF
WATER.FLOODING WILL REDUCE TEMP TO SAFE LIMITS.PROVIDE ELECT GROUND
TO AVOID STATIC DISCHA RGE IN EXPLO ATMS/PREVENT HANDLERS (SUP)

Respiratory Protection:WHERE NATURAL VENTILATION IS INADEQUATE USE
MECHANICAL VNETILATION, OTHER ENGINEERING CONTROLS OR TOXIC DUST
RESPIRATORY(NIOSH/MSHA APPROVED) TO PREVENT INHAL OF DUST.
Ventilation:WHERE NATURAL VENTILATION IS INADEQUATE USE MECHANICAL
VNETILATION OR OTHER ENGINEERING CONTROL.
Protective Gloves:USE GLOVES.
Eye Protection:SAFETY GLASSES OR GOGGLES.
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:WASH HANDS AFTER HANDLING.
Supplemental Safety and Health
DECOMPO PROD:PROD ITSELF DOES NOT READILY DEOCMPOSE UNLESS SUBJECT TO
EXTREME TEMP/CHEM CONDITIONS.IF SO WOULD INCLUDE MIX OF OXIDES
SHOWN IN INGREDS. 1STAID:CONTAIN MATL OF HAZ NATURE.ID THAT MATL &
TREAT SYMPTOMATICALLY. OTHER PRECAUTIONS:RECEIVING STATIC SHOCKS.
DISPOSAL:DISPOSE ACCORDINGLY.

HCC:V7
Spec Gravity:1.1 PC, 2.1 CRY
Solubility in Water:NOT AVAILABLE
Appearance and Odor:ODORLESS TAN PELLETS, GRANULES, BEADS OR WHITE
POWDER OR CAKE.

Stability Indicator/Materials to Avoid:YES
SUDDEN CONTACT W/HIGH CONCEN OF CHEMICAL HAVING HIGH HEATS OF
ADSORPTION SUCH AS OLEFINS, HCL, ETC.
Stability Condition to Avoid:ADDN OF MOISTURE (WATER W/O FLOODING CAN
CAUSE RISE IN TEMP FRN HEAT OF ADSORPTION & SKIN CONTACT MIGHT
RESULT IN BURNS.
Hazardous Decomposition Products:HDYROCARBONS,OTHER MATLS THAT CONTACT
PROD DURING USE CAN RETAIN IN PROD.DECOMPO PROD FRM THESE RETAINED
MATL.(SUPPLE)

Waste Disposal Methods:MSDS:DISCARD PROD,RETAINED MATL OF
USE,DISPOSABLE CNTNR,LINER IN ENVIRO ACCEPTABLE MANNER IN FULL
COMPLIANCE W/ALL APPLICABLE GOVT REGS.NOTE:PROD DESICCANT &
GENERATES HEAT AS ADSORBS WATER.USED PROD CAN CONTAIN MATL OF HAZ
NATURE.ID THAT MATL (SUPP)

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.